Exterior Paint Semi-Gloss DULUX SUPERCOTE NANOTEX 9 L A915 Base A

• Supercot Nanotex Tight adhesion to the homogeneous wall. With a special detail latentex
• with low water absorption properties Causing not to accumulate water and moisture in the wall.
• Helps the building to be beautiful, durable, not peeling, swollen, swollen.
• Smooth color film Can eliminate dust And stains easily.
• High quality color powder Prevent and reflect the heat from sunlight-UV rays
• contain prevention, mold and lemongrass, including anti-alcohol, salt.
• There is no mixture of lead and mercury. Safe for users.
• Suitable for concrete surfaces, bricks, plaster, gypsum fiber cement sheets.
• 9 liters
• Base A

Technical information

• Color type: acrylic watercolor
• Color film characteristics: semi-shadow
• color texture by volume : 30-40%
• Dry duration: not less than 30 minutes.
• Apply duration: 30 minutes - 2 Hours
• Delivery duration: at least 7 days
• Covering the theory : 35-40 sqm/trip/US gallon

How to use

• Equipment: Apply with a spray brush
• Mix before use. : Can be used immediately Or if wanting to mix, add 1 part clean water per 10 parts (10%)
• Cleaning : Wash the equipment with water immediately after use.
• Wipe the paint film. : Should be dry for at least 14 days. Before washing, clean.
• The recommendation of the use of dark colors: the natural color of the bright color is limited to the cover. May have to increase the amount of coolness Or foundation with a lighter color in the same shade.

Painting System

• Before every paint The surface must be dry, clean, free from dust, cement scraps, fat stains and dirt.
• If there are no more than 1 mm wide cracks, repair with porn paint, supercat acrylic (A952-400) and then scrub it smoothly.
• Should make sure that the wall does not have water leakage. To protect the color film later.

Preparation of the surface

• New cement surface never painted Or painted and the color is still in good condition.
  • Leaving the surface of the cement completely dry at least 1 month after plastering with no more moisture. 14%
• Old cement surfaces that deteriorate
  • should scrub the original color that has deteriorated.
  • The area Fungal Or moss Wash with clean water, then dry, then apply with water, fungus and moss. Look at Luxewet Mold Mold, by tinging overnight.
  • Then scrubbing out as well. The water is clean, leave to dry completely.
  • Polishing or removing color film by heat can cause dust. or dangerous tear If you can do it, you should use the polishing of brush and water instead.
  • Should work in a place that is convenient to ventilate. And wearing the appropriate protection device.

Painting foundation

• Floor New plaster skin never painted. Or painted and the color is still in good condition.
  • Painted new cement foundation, alkaline, Super coat, A917-800, 1 trip.
  • Leave for at least 30 minutes - 2 hours before painting. Overlapping
• Old cement surface deterioration Is a dust, chalk or synthetic wood Fiber cement or surface that uses smooth plastering materials
  • Apply 1 Super Cotton A538-600 cement foundation.
  • Leave at least 10-12. Hours before painting on the top

Painting on top

• Painted with colors Supercott Nanotex for exterior for at least 2 trips.
• Leave the distance between the first and next layer of color. About 30 minutes - 2 hours

Additional suggestions

• Should be stored in a dry temperature, close the lid. Close to the hand of the child.
• Please see the caution that is attached to the container.
• Color work should be done in a place where the air is convenient.
• Should Wear a mask when spraying And avoiding the skin from touching the skin Or inhalation. If entering the eyes, should wash with clean water immediately. And hurry to see a doctor.

Note : The color of the product shown on the website There may be different from the color display settings of each screen.