KANGAROO Masonry Mortar for Lightweight Block (CP007), 40 KG

• Light weight brick laying mortar, dry type, quick, reducing steps, no need to pour water on bricks before laying.
• Has special properties for high adhesion. Strong adhesion in 10 seconds
• It is tough, can withstand force quickly, does not crumble, has time to shape the construction before it hardens.
• Fine cement texture, easy to align, thin construction, no wasted cement.
• For construction of non-Load Bearing lightweight brick walls and Load Bearing lightweight brick walls with a construction thickness of only 2 - 3 mm.
• Used for building walls inside and outside buildings.
• Packaging size 40 kg.

Technical information

• Area of use (sq m/bag)
• Made of lightweight brick, 7.5 cm thick, able to build 26 sq m.
• Made of lightweight brick, 10 cm thick, able to build 19.5 sq m.

How to use

• Preparation
  • Use a broom to clean all the dust from the bricks. And there is no need to sprinkle water on the lightweight bricks. Can be dried immediately
• Mixing
  
  • Purple Kangaroo Cement 40 kilograms (1 bag): 10.5-12.0 liters of water or 2.5 parts Purple Kangaroo Cement to 1 part water by volume, stir the cement to mix. Homogeneous, not granular. By stirring with an electric drill to mix the cement. It should take at least 3 minutes to stir, making sure that it is uniform and not granular. Then leave it for about 5 minutes for the chemicals to break down. Then stir again before use.
• Mix with machine
  • Stirring with an electric drill to mix the cement should take no less than 3 minutes, making sure it is uniform and not granular. Then leave it for about 5 minutes to allow the chemicals to break down, then stir again and use it to build.
• Mix by hand
  • manual stirring You should use a Bodhi leaf trowel to stir for a long time, making sure that the cement is not granular and then leave it for about 5 minutes to allow the chemicals to break down. Then stir it again and use it.
• work
  
  • Hold the lightweight brick and tilt it to the ground. Use a masonry trowel to scoop up the cement mixed in the can to fit the cement sign. Apply the masonry mortar by swiping the long trowel to cover the entire face of the lightweight brick ridge. and the
    • head side of the lightweight brick At a thickness of approximately 2-3 mm., observe the liquid consistency as follows.
    • If the cement is too liquid, the comb lines will fall out of place. When knocking bricks on the floor Solved by adding cement mixture again.
• Place lightweight bricks coated with cement. Take the ridge side that was applied with the construction adhesive and place it on the lightweight brick line. Use a rubber mallet to make adjustments to the alignment and then tap the bricks to firmly adhere. The cement will come out. Use a Bodhi leaf trowel to smooth out the cement. Then the next lump can be formed immediately.

Tile adhesive work

• Preparation
  
  • Prepare clean tiles. and dry before laying tiles (Do not soak tiles in water)
  • The surface to be tiled must be smooth and level. The leveling surface must be strong and not crumbling.
  • In the case of wet areas such as bathrooms and kitchens, a waterproofing system should be installed before laying tiles to reduce water leakage problems.
• Mixing
  
  • Purple kangaroo cement 40 kilograms (1 bag): 10.5-12.0 liters of water or 2.5 parts purple kangaroo cement to 1 part water by volume. Stir the cement until the mixture is uniform and not granular. By stirring with an electric drill to mix the cement. It should take at least 3 minutes to stir, making sure that it is uniform and not granular. Then leave it for about 5 minutes to allow the chemicals to break down and then stir again before using.
• Mix with machine
  • Stirring with an electric drill to mix the cement should take at least 3 minutes to make sure it is uniform and not granular. Then leave it for about 5 minutes to allow the chemicals to break down, then stir again and use it to build.
• Mix by hand
  • manual stirring You should use a Bodhi leaf trowel to stir for a long time, making sure that the cement is not granular and then leave it for about 5 minutes to allow the chemicals to break down. Then stir it again and use it.
• work
  
  • Spread the cement adhesive with a notched trowel according to size. (depending on the size of the tile) in a long way on the work surface Then lay the tile over the cement glue that was screed, press firmly and use a rubber mallet to tap on the tile thoroughly. so that the grooves of the cement glue behind the tiles Press together thoroughly. The groove for grouting should be at least 2 mm.

Note: Product colors shown on the website There may be differences from the color display settings of each screen.